一個偶然的機會，KM Formenbau在展會上看到了m&h在機測量方案的演示，立即決定訂購一臺配有m&h測頭的機器?，F(xiàn)在公司的機床測頭已經全部更換為m&h品牌的機床測頭。這對m&h來說是輕而易舉的，他們的測頭可以和其它廠家的紅外接收器無縫兼容。

KM Formenbau工廠安裝了一套m&h在機測量軟件3D Form Control,自安裝以來，該軟件在KM Formenbau工廠運行良好，沒有出現任何問題。一套3D Form Inspect軟件支持了現場的四臺機床，并共享了所有的測量程序。在實際測量開始之前，軟件會根據用戶使用測頭角度的不同，自動生成校驗程序并執行（已獲保護）。當然，用戶也可根據現場情況，直接進行工件測量。通常，測量前實施校驗是必需的，尤其是對于高精度測量來說。此種方法可以有效補償機床熱影響和旋轉軸系統誤差的影響。補償后的測量結果可以和三坐標測量機（CMM）的測量結果保持*。

 

---

m&h Radio-wave Touch Probe RWP20.41

The touch probe RWP20.41 has been designed for complex measuring tasks. Modular extensions enable measuring inside the workpiece or in deep cavities. The freely adjustable trigger force allows both triggering on very thin-walled workpieces at minimum trigger force and the use of heavy cross probes at maximum...

» more

m&h Radio-wave Touch Probe RWP38.41

The compact radio-wave touch probe RWP38.41 has been developed for machines requiring signal transmission across greater distances where infrared transmission is not sufficient. It is ideally suited for use on machine tools with limited maximum tool diameter and restricted height of the Z axis, particularly with 5-axis heads. It can be extended in a modular way and is the perfect solution for complex measurements. Thanks...

» more

m&h Temperature Probe RWTP20.44

The temperature probe RWTP20.44 is intended for use on large machining centres and 5-axis machines when infrared transmission is not sufficient. It acquires, fully automatically, the part temperature before and during the machining （patented）. This enables improved control of the production process and tuning of machining parameters during ongoing production. Temperature-dependent parameters can thus be determined with certainty before the...

» more

m&h Radio-wave Tool Setter RWT35.50

The Radio-wave Tool Setter RWT35.50 for vertical lathes, large milling machines and machining centers enables variable positioning of the tool setter, to fit the task at hand. Through use of a magnetic mount, the tool setter can be placed in wide range of table positions. Our patent pending system delivers highly accurate and repeatable re-positioning of the tool setter. With wireless operation and no permanently fixed hardware, use of...

» more

m&h Radio-wave Receiver RWR95.40

The compact radio-wave receiver RWR95.40 communicates with all m&h radio-wave probes, including the temperature probe. It is sealed to IP68 and can be mounted anywhere in the machining area with ease. Measurement and temperature data are transmitted using the high-penetration transmitting frequency of 433 MHz. While in operation, the environment is continuously checked for interference from transmitters （SCS）. Corrupted channels are...